Russian 
English 
Spanish For an NGZ Высокая эффективность загустителя purchase, these details belong in the equipment enquiry. Hexin’s published NGZ information covers controlled feeding, degassing and multipoint addition; it does not remove the need to define the reagent package for the actual plant.
What does dose mean on a purchase document?
“Dose” is not a complete duty by itself. Two proposals can use the same word while describing different quantities.
Put the basis beside the number
Write the slurry flow and dry-solids rate as ranges. The selected reagent should be named. Then say whether the laboratory result is expressed per tonne of dry solids, per litre of slurry, or on another basis. Keep the prepared-solution concentration beside that calculation; otherwise the pump flow is easy to misread. A litre of dilute polymer does not contain the same reagent mass as a litre of a stronger solution.
That is why pump flow by itself makes a poor comparison. When the solids rate moves away from its daily average, the calculation should still show what the pump is expected to deliver.
What belongs in polymer preparation?
The first practical question is the product form: powder, emulsion and liquid each arrive with different preparation work. The chemical supplier’s instructions are the starting point, but the equipment quotation has to show what happens at the plant.
Follow one batch from water to service
The quotation should say how the product is wetted, mixed and held. It should also identify preparation concentration, usable tank volume, transfer equipment and the point at which the solution becomes ready. If a new batch needs waiting time, explain what supplies the thickener during that interval.
A shift change is a useful test of the scope. Can the operator see which batch is ready? Is there reserve volume when demand rises? List reagent tanks, mixers and pumps explicitly. An NGZ quotation does not automatically include a complete polymer preparation plant.
Where does dilution water enter the process?
Preparation water and later dilution water are separate streams. Slurry dilution at the feedwell is another duty again. Mixing them in one line on the enquiry makes the plant water balance hard to review.
Mark the connection and its measurement point
A water line is easier to review when its source, pressure, flow and relevant analysis appear beside it. Recycled water needs an expected range, rather than a simple note that it is available. “Water is available” does not show that it suits the selected polymer.
The supplier should mark the prepared-solution measurement point and the later dilution point. With those points marked, the drawing tells the same story as the plant water balance.
How will the solution meet the slurry?
The injection arrangement connects the dosing package with the NGZ feed system. It needs to be shown in a way that an operator and a commissioning engineer can both follow.
Keep the laboratory arrangement visible
Hexin describes multipoint addition. A useful quotation makes that phrase concrete by showing the points, delivery route and operating modes. If different points are used for different duties, say how the change is controlled.
The laboratory record should leave a note about how reagent and slurry were mixed. If the site feed differs, describe how that difference will be checked. Degassing is a specific question for the selected NGZ package, not a label that explains every installation.
What should commissioning prove?
A pump running at its set speed proves movement. It does not prove solution concentration, delivered flow or stable clarification.
Agree on evidence before startup
А thickener sizing guide stresses representative feed; the same care should be used for dosing checks.
An empty solution tank and missing dilution water should be covered in the controls description. Alarm and restart responses belong in the project scope, where they can be reviewed before the first shift.
What can Hexin provide?
Янтай Гексин Экологическая защита оборудования Co., Ltd supplies industrial filtration equipment, including NGZ thickeners, and provides after-sales service. Its published NGZ information identifies controlled feeding, degassing and additive addition. Feed ranges and settling-test data give Hexin a useful basis for product details and a quotation. Ask the proposal to separate preparation, storage, dilution, injection and plant-service responsibilities.
Вывод
Start with a clear dose basis. Trace the reagent through preparation, dilution and injection on the process drawing. Put the test conditions beside the proposed pump and tank duties, then agree on the checks before startup. With those details together, commissioning staff have something they can check line by line.
Вопросы и ответы
Can a dosing pump be selected from slurry flow alone?
No. Reagent basis, solution concentration and dry-solids range also determine the duty.
Is one preparation time suitable for every flocculant?
Use the selected chemical supplier’s instructions. Product form and preparation conditions vary.
Is a polymer preparation package automatically included with an NGZ?
The quotation should list tanks, mixers, pumps and water connections explicitly.
